I am configuring Strongswan server for VPN clients to access internal network (EAP-IKEv2). I set it up successfully using self-signed server certificates and it works for clients using Mac OS X, Windows 7 and Windows 10 after adding ca.crt to the clients' Root CA's as trusted.
The IKEv2/IPsec connection method is one of the alternative options for connecting to NordVPN servers on your Windows PC.This connection method is preferred by privacy enthusiasts, as IKEv2/IPsec security protocol is currently one of the most advanced in the market. Dec 29, 2018 · Mobility enabled for IKEv2 = Yes. Here's the VPN info: Name : xxx. ServerAddress : (sorry but this is not allowed to leak) AllUserConnection : False. Guid : {D385C26C-1930-4809-B76C-E44C89BC4F1E} TunnelType : Ikev2. AuthenticationMethod : {Eap} EncryptionLevel : Optional. L2tpIPsecAuth : (22) eap: Finished EAP session with state 0xe44cdc41e470d83d (22) eap: Previous EAP request found for state 0xe44cdc41e470d83d, released from the list (22) eap: Peer sent packet with method EAP MD5 (4) (22) eap: Calling submodule eap_md5 to process data (22) eap: Sending EAP Failure (code 4) ID 60 length 4 (22) eap: Freeing handler (22) [eap For EAP-RADIUS with IKEv2 you need to create a Root CA and a server certificate for your Firewall. Go to System ‣ Trust ‣ Authorities and click Add. Give it a Descriptive Name and as Method choose Create internal Certificate Authority. Increase the Lifetime and fill in the fields matching your local values. Configure EAP-TLS (cert-based) authentication Notes: Smart Card or other certificate is the EAP-TLS authentication method. For the device to be able to find and use the correct certificate for the connection you need to configure EAP-TLS properties for your environment including the “Advanced” page. Zu Inhalt springen; Zu Breadcrumbs springen; Zu Überschriftmenü springen; Zu Aktionsmenü springen; Zu Schnellsuche springen Configuring IKEv2 Ports. To configure the IKEv2 ports and EAP protocol: Select System > Configuration > IKEv2 to display the configuration page. See Figure 169. Enter the DPD timeout value in seconds. Valid values are 400-3600. DPD is a form of keepalive.
Nov 13, 2018 · crypto ikev2 policy ikev2policy proposal ikev2prop!! crypto ikev2 profile ikev2profile match certificate MAPS authentication remote rsa-sig authentication remote eap query-identity authentication local eap mschapv2 username cisco password cisco pki trustpoint TEST! crypto ikev2 disconnect-revoked-peers!! crypto ipsec transform-set trans esp-aes
But as EAP-TLS is a mutual authentication protocol, EAP-only authentication can be used by specifying leftauth=eap. Certificates for EAP-TLS are configured the same way as for traditional IKEv2 certificate authentication, using ipsec.d/cacerts , ipsec.secrets and leftcert= / rightcert= . RFC 5998 Extension for EAP in IKEv2 September 2010 1.1. Terminology All notation in this protocol extension is taken from . Numbered messages refer to the IKEv2 message sequence when using EAP. Thus: o Message 1 is the request message of IKE_SA_INIT. o Message 2 is the response message of IKE_SA_INIT. Vigor3900 and Vigor2960 support IKEv2 with EAP authentication since firmware version 1.4.0. It can make IKEv2 VPN even more secure by additional username and password authentication and certificate verification. This article demonstrates how to create a self-signed certificate for server authentication, set up Vigor Router an IKEv2 VPN server, and how to establish a connection from Windows by May 19, 2011 · For EAP authentication, Microsoft Windows 7 IKEv2 client expects an EAP identity request before any other EAP requests. Please configure the query-identity argument in IKEv2 profile on IKEv2 RA server to send an EAP identity request to the client.
2. Configuration⌗ 1. ipsec/swanctl⌗. Example ipsec.conf with username and password (NordVPN uses a different approach, see below):. conn vpn keyexchange=ikev2 dpdaction=clear dpddelay=300s eap_identity="" leftauth=eap-mschapv2 left=%defaultroute leftsourceip=%config right= rightauth=pubkey rightsubnet=0.0.0.0/0 rightid=%any type=tunnel auto=add
Configuring IKEv2 Ports. To configure the IKEv2 ports and EAP protocol: Select System > Configuration > IKEv2 to display the configuration page. See Figure 169. Enter the DPD timeout value in seconds. Valid values are 400-3600. DPD is a form of keepalive. IKEv2 EAP for the VPN type 192.0.2.1 for the server field the login/password values set in the responder config the newly imported CN=VPN CA certificate for the CA certificate field client1.domain for the User identity field server1.domain in the Server identity field (under 'advanced settings') For EAP-MSCHAPv2 with IKEv2 you need to create a Root CA and a server certificate for your Firewall. Go to System ‣ Trust ‣ Authorities and click Add. Give it a Descriptive Name and as Method choose Create internal Certificate Authority. Increase the Lifetime and fill in the fields matching your local values. Aug 13, 2019 · IKEv2/IPSec. What is IKEv2/IPSec? IKEv2 is a tunneling protocol that is standardized in RFC 7296 and it stands for Internet Key Exchange version 2 (IKEv2). It was developed as a joint project between Cisco and Microsoft. To be used with VPNs for maximum security, IKEv2 is paired with IPSec. Nov 13, 2018 · crypto ikev2 policy ikev2policy proposal ikev2prop!! crypto ikev2 profile ikev2profile match certificate MAPS authentication remote rsa-sig authentication remote eap query-identity authentication local eap mschapv2 username cisco password cisco pki trustpoint TEST! crypto ikev2 disconnect-revoked-peers!! crypto ipsec transform-set trans esp-aes